The quick-frozen warehouse is easy to load and unload. All the plates and walls of the quick-frozen warehouse are produced by molds. You can choose tens of millions of products. Professional cold storage installation， installation of cold storage cold storage construction， fruit preservation cold storage， medical cold storage and transaction safety are guaranteed. Through internal concave convex groove connection， loading， unloading and handling are convenient. The installation period is short. Small and medium-sized cold storage can be delivered in - days， The library body can be combined， separated or increased or decreased according to the needs of users.
The selection of cold storage is very important for cold storage， because cold storage is different from ordinary cold storage. The temperature in cold storage is usually low， and the air temperature， humidity and environmental requirements are relatively high. When selecting cold storage， attention must be paid to the selection of cold storage with better temperature. If the selection of cold storage is not good， the temperature in the cold storage is difficult to which is easy to cause the deterioration of products in the cold storage， or the refrigeration compressor in the cold storage often works， wasting more resources and increasing the cost.
FloridaDo not cut off the main power supply to shut down the unit unless it is an emergency; If the unit is out of service for a long time in winter， turn off the unit first， then turn off the main power supply and oil heater， and drain the water in the system.
Cold storage design segmentation: several different partitions shall be reasonably planned and divided according to purpose and temperature. For example: processing room， sorting room， quick freezing room， channel unloading platform， etc.
IndasilaneThe two sets of connectors between the cold storage shall be wedged tightly， and the two sets of connectors shall be fixed at the upper， outer and lower sides of the cracks in the cold storage respectively. The lower connector shall be as close as possible， so as to facilitate the use of concrete to cover the connector in the future.
The wide， light and thin walls are made of rigid polyurethane foam at the same time as structural materials， making the whole structure have the advantages of light weight， large span and high load. The thinner polyurethane sandwich plate can meet the relevant provisions on building energy consumption limit， which allows the use of thinner plates during construction and saves building space.
The service life of the cold storage depends on the quality of the refrigeration equipment， but it also has a great relationship with the proper daily management and maintenance after the installation of the cold storage. Many times， people often ignore the latter point. In daily life， as long as we maintain and maintain the cold storage regularly， we can greatly improve the service life of the cold storage and reduce the cost.
The installation of top warehouse plate should be carried out alternately with the installation of wall plate， and the wall plate should leave a gap for withdrawing construction equipment; During the installation of the top warehouse plate， the end steel sheet at the overlap with the wall plate shall be disconnected for mm to prevent the cold bridge from running cold; Two layers of foaming materials shall be evenly and continuously punched on the joint surface between each top warehouse plate. Rivets shall be pulled and fixed at the internal and external lap joints of the steel plate， and the rivet spacing shall be mm; According to the design drawings， if there are supporting beams， columns and supporting steel frames in the warehouse the setting out and positioning shall be carried out and accurate and clear marks shall be made according to the requirements of the design drawings; Weld or install the support beam， column， support steel frame， etc.， and the welded junction shall be moisture-proof and treated according to the drawing requirements.
Whether the warehouse can drill through the wall. The construction and installation of cold storage shall be like the installation of air conditioner， and the external unit shall be connected with the unit in the cold storage.
With the development of the times， refrigeration devices are becoming more and more common. All aspects of life are inseparable from its use. Families will also be equipped with some simple refrigeration devices. For refrigeration devices such as cold storage， it is important to select materials with good thermal insulation. Cold storage is a better material selection，FloridaPrice of fruit preservation warehouse， and manufacturers need to grasp its key points in the production process of cold storage.
total costInstall the electric control system. The electric control system of the cold storage mainly includes electric controller，FloridaProfessional installation of cold storage， electric door， lighting and other electrical equipment in the cold storage. The power supply of the cold storage is required to be stable phase line， and the power supply or backup power supply can be used as required. The circuit shall have reasonable discharge and corresponding protective measures.
Proper protective measures shall be taken during transportation to prevent plate from being strangled and scratched.
The refrigerator compressor unit generally adopts high-end units with guaranteed quality and strong operation stability. The evaporator adopts the imported joint venture refrigeration air-cooled evaporator， which can effectively meet the refrigeration capacity of the refrigerator and ensure the refrigeration effect of the refrigerator. The refrigerator lamp adopts the special LED energy-saving lamp for the refrigerator， which has the advantages of low temperature resistance， low energy consumption and long service time， It can effectively save the operation cost of cold storage.
Polyurethane spraying is widely used in large and medium-sized refrigerators. Different well-known brands are produced at different prices， and the product quality is relatively large. However， it is not high-quality or good goods. This is the result of long-term cooperation.
device managementThe two sets of connectors between the cold storage shall be wedged tightly， and the two sets of connectors shall be fixed at the upper， outer and lower sides of the cracks in the cold storage respectively. The lower connector shall be as close as possible， so as to facilitate the use of concrete to cover the connector in the future.
This high-quality CA library not only wants to bring a certain effect in use， but also wants the hot air fan to reduce energy consumption in use. Every customer wants to achieve a better return with less investment. Therefore， today， I will introduce how the CA library can achieve energy-saving effect.
Emergency measures during the use of the medical cold storage project， it may also encounter power failure or power failure. In fact， the cold storage door should be closed in time， So as not to expose more air conditioners， resulting in corresponding problems in the quality of stored products. The medical cold storage project also has a self rescue system in time. If the temperature of the cold storage exceeds the limit， the system cooling system will also be turned on. When the temperature returns to normal， it will be automatically turned off.
FloridaPolystyrene foam: polystyrene foam is a new type of synthetic thermal insulation material. It is a kind of plastic， with small density，FloridaHow long can the fruit be kept fresh in the cold storage， light weight， due to its cold shrinkage， it is not very convenient for installation.
Polyurethane foam: This is also a very common cold storage material. It has strong thermal insulation effect and strong mechanical strength. Now it is widely used and has a good application prospect.
It is required to set up a special tally room (area)， and the temperature of the tally area is usually controlled at ~ + ℃.
